Epson Stylus Color 1520 Ink Jet Printer Guía para resolver problemas descargar pdf (Pagina 6)

EPSON Stylus COLOR 1520

6 - EPSON Stylus COLOR 1520 5/97

Testing the Printer

You can run a printer self test to determine whether the

problem lies with the printer itself or some other source.

❏ If the test results are satisfactory, the problem lies in

software settings, the interface cable, or your computer.

❏ If the test pages don’t print correctly, you may have a

problem with your printer. See the suggestions in this

chapter for possible solutions.

Follow these steps to test the printer:

1. Load several sheets of paper in the built-in sheet feeder,

making sure the right edge guide is positioned correctly for

your paper’s width and the paper release lever is in the single

sheet position.

2. Turn off the printer.

Caution:

Use paper that’s at least 8.3 inches (210 mm) wide so

ink doesn’t spray onto the platen.

3. Hold down the Load/Eject button and press the

POperate button to turn on the printer. Then release

both buttons. This prints the test pages at 360 dpi. (To

print test pages at 180 dpi, hold down the

LF/FF button

while turning on the printer instead of

Load/Eject.)

The first page prints on the first and last lines to measure

the page length. The next page contains a nozzle check

pattern and the printer’s ROM version, along with

multicolored character samples. (The 180 dpi test prints

black character samples.)

If the test pages don’t print, turn off the printer. Then

repeat this step, holding down the

Load/Eject button a bit

longer before releasing it.

Caution:

Never turn off the printer while it’s printing test pages.

Always press the Pause button and eject any loaded

paper first.

4. After the second page prints, press the Pause button to stop

test printing.

5. If the printer loaded any additional paper, press

Load/Eject

to eject it. Then turn off the printer to end the test.

Operate

The Operate light is on when the

printer is on. When the

Operate light

flashes, the printer is receiving data. It

may also flash with other lights during

other operations or error conditions.

Paper Out S

When the Paper Out light comes on,

your paper ran out or is loaded

incorrectly, or the paper release lever is

set to the wrong position. Load paper,

check the lever position, and then press

the

Load/Eject button to turn off the

light. If the

Pause light is on, press the

Pause button to turn it off.

When the

Paper Out light flashes, you

have a paper jam. Turn off the printer

and gently pull out all jammed paper.

Reload the paper, then press the

Load/

Eject

button to turn off the light. If the

Pause light is on, press the Pause

button to turn it off.

Ink Out B

Ink Out I

When an Ink Out light flashes, your ink

supply is low. Make sure you have a

replacement cartridge.

When an

Ink Out light comes on, you

need to replace the ink cartridge.

Pause

When the Pause light is on, printing is

paused. Press the

Pause button to

resume.

When the

Pause light flashes, your

printer is charging ink, cleaning the

print heads, or performing another

operation.

If you need to reset the printer’s

memory, hold down the

Pause button

for 5 seconds.

Cover Open

When the Cover Open light comes on,

the printer’s cover is open and printing

is paused. Close the cover. If the

Pause

light is on, press the

Pause button to

turn it off and resume printing.

All the lights

When all the lights flash, your printer

may have an internal error.

1 2 3 4 5 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios

Epson Stylus Color 1520 Ink Jet Printer Guía para resolver problemas Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo Epson Stylus Color 1520 Ink Jet Printer