PixiePlus™Projector Controller for Epson® Installation Guide(Decora™ wall plate not included)ELPSP10Patent US 7,334,067

9V. Reprogram PixiePlus cont’d1. Power the PixiePlus: the LED backlights will be illuminated.2. Enter learning mode: Gently insert a paper clip into

10V. Reprogram PixiePlus cont’d4. Round Robin Codes and MacrosEach PixiePlus button may be programmed with either a single command or multiple command

11V. Reprogram PixiePlus cont’dYou may press a different button for learning at any time, including buttons that have already been programmed. If you

12V. Reprogram PixiePlus cont’dProgram the button, and it will again beep three times to indicate if the code was successfully learned. Repeat as many

13V. Reprogram PixiePlus cont’dIf the button did not seem to learn correctly, press any other button on the PixiePlus, then press the target button ag

14V. Reprogram PixiePlus cont’dOne PixiePlus may learn IR commands from remote controls from different devices. Each button can be configured to send

15VI. Configuring Special Features1. Inactivity Shutdown timerThe Inactivity Shutdown Timer will automatically shut the display device down if it is n

16VI. Configuring Special Features cont’dTo change the active setting: Press VOLUME UP or VOLUME DOWN to cycle to the next setting. The PixiePlus will

17VI. Configuring Special Features cont’dIf the entered code is not correct, the system emits a long beep and remains locked.Security Keycodes may be

18VI. Configuring Special Features cont’d3. PixiePlus Audio FeedbackBy default, the PixiePlus clicks when a button is pressed. To mute, press and hold

1Important Safety Instructions1) Read these instructions. 2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use thi

19VI. Configuring Special Features cont’dIt will time out of cloning mode in about 15 seconds, so have both devices on hand. If the PixiePlus times ou

20IX. OperationPowerPower buttons control power on the projector or monitor. The PixiePlus is always on, and its LED backlit buttons remain continuall

21X. TroubleshootingProgramming ProblemsVerify that the PixiePlus is in learning mode for programming. The Status LED continually blinks red when the

22Is the PixiePlus display dark, and does it chirp when any button is pressed? If so, the PixiePlus Security Keylock is active. See page 16 for inform

23WarrantySP Controls warrants all PixiePlus products and accessories against defects in materials and workmanship for a period of five years from the

I. IntroductionPreconfigured for Easy Setup The PixiePlus (PXE-DCM+) Projector Controller for Epson® (ELPSP10) is a single-gang AV control device conf

II. Installation OverviewBezel Single-Gang Wall BoxCircuit BoardInsertsThe Projector Controller for Epson ships with:• 1 PixiePlus Circuit Board• 6 Wh

4III. PixiePlus InstallationThe Projector Controller for Epson is preconfigured to use the Discrete Power, 4-Button Source, and Volume Control button

5III. PixiePlus Installation cont’d2. Attach BezelBe sure the bezel is placed right-side-up. The SP Controls logo should be right-side up.Bezel Inser

6Installation OverviewPXE-DCM+PXE-DCM+ 6VDCPower SupplyRS-232 Serial Cable1. Connect the cable assembly (emitter block) to the display via the serial

7IV. Wiring PixiePlus to Display Device cont’dV. Reprogram PixiePlusThis section describes how to reprogram the PixiePlus control codes, which will no

8Toggling Source Module Between 2-Button and 4-Button Mode (optional)By default, the PixiePlus is configured to work with a four-button source module.