Epson LQ 670 - B/W Dot-matrix Printer Instrucciones de operaciones Pagina 1

24-Pin Do t M a trix Printe rAll rights reserved. No part of this publication may be reproduced, stored in a retrievalsystem, or transmitted in any fo

Chapter 5 Using Printer OptionsCut-Sheet Feeders . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2Installing th

Loading paper from the second-bin cut-sheet feederFollow the steps below to load paper in the second bin of thedouble-bin cut-sheet feeder.Note:Y ou c

2. Load a fanned stack of paper (up to 50 sheets), aligning the right edge of the paper with the right paper guide. Be sure toload the paper with the

Switching between the tractor and the cut-sheetfeederYou can easily switch between continuous paper loaded from thetractor and single sheets loaded fr

Loading paper manually from the sheet guideThe cut-sheet feeder’s single-sheet loading feature allows you toswitch to a different type or size of pape

Ro ll Pa p e r Ho ld e r The optional roll paper holder (#8310) allows you to use yourprinter with 8.5-inch roll paper like that used in telex machine

3. Position the roll paper holder beneath the printer as shownbelow. Fit the two holes in the roll paper holder base under the two positioning pegs on

Loading a roll of paperTo load a roll of paper on the roll paper holder, follow these steps:1. Cut the leading edge of the roll paper straight across.

3. Bring the leading edge of the paper up over the paper path guide and insert it into the printer until you feel resistance.The printer loads the rol

Interfa ce Ca rds You can use optional interface cards to supplement your printer’sbuilt-in parallel interface. The EPSON interface cards below areco

2. Remove the screws securing the shield plate to the back of theprinter and remove the plate.3. Slide the interface card along the slots on both side

Appendix A SpecificationsTechnical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . A-2Printing . . . .

Using a serial interface card (C82305✽ or C82306✽)To use a serial interface card (C82305✽ or C82306✽ ), see thesections below to set the correct baud

Chapter 6Maintenance and TransportationProof Sign-off:Ya n o _______Kim ura _______Gra d y _______No ru m _______Replacing the Ribbon Cartridge . .

Replacing the Ribbon Cartridge If your printing becomes faint, you may need to replace the ribbon cartridge. (See Chapter 7, “Troubleshooting,” for mo

2. Make sure the print head is at the ribbon installation position(the middle position where the front metal plate is indented),as shown below. If the

4. Remove the new ribbon cartridge from its package and turn the ribbon-tightening knob in the direction of the arrow toremove any slack in the ribbon

6. Turn the ribbon-tightening knob again to remove any slack in the ribbon and to make sure the ribbon moves freely.7. Close the printer cover.Cleanin

cCaution:❏Never use alcohol or thinners to clean the printer; thesechemicals can damage the printer components as well asthe case.❏Be careful not to g

Chapter 7TroubleshootingProof Sign-off:Ya n o _______Kim u ra _______G ra d y _______No rum _______Using the Error Indicators . . . . . . . .

This chapter describes what you can do if you are havingproblems printing. It is divided into these sections:❑Using the error indicators. This section

Using the Error Indica tors You can identify many common printer problems using thelights on the control panel. If your printer stops working andone

Appendix C Contacting Customer SupportFor United States Users . . . . . . . . . . . . . . . . . . . . . . . . . C-2Electroni

Printing a Self Test Running the printer’s self test helps you determine whether the problem comes from the printer or the computer:❑If the self test

After a few seconds, the printer loads the paper automatically, and then begins printing the self test. A series of characters is printed.Note:To temp

3. Open a software program and send a print job to the printer.Your printer prints all the codes it receives in hexadecimalformat.By comparing the cha

Power supply The lights come on briefly but then go off and stay off.Cause What to doThe printer’s voltage ratingdoes not match the voltage of your el

Paper handlingSi ngle sheets loaded from the paper guideThe printer does not load single-sheet paper. Cause What to doContinuous paper is in thepaper

Paper feeding is crooked or the paper jams.Cause What to doThe paper guide is notproperly installed.Remove the paper guide and install itas described

When the printer ejects the paper, the Pa p e r O ut light flashesand the Pa u se light comes on.Cause What to doThe printer has not fullyejected you

Paper feeding is crooked or the paper jams.Cause What to doThe paper supply isobstructed.Make sure the paper supply is notobstructed by a cable or som

The top-of-form position of your continuous paper varieswhen you print several pages.Cause What to doThe paper size setting in yourapplication or the

The printer’s page lengthsetting may not match thesize of the paper you areusing.Check the “Page length for tractor”setting using the printer’sdefault

IntroductionYou r new EPSON® 24-pin dot matrix printer offers highperformance with a wide range of features in a compact design.You will find the sam

Single sheets loa ded from the optional cut-sheet feederThe platen rotates but the cut-sheet feeder does not feed thepaper.Cause What to doThe cut-she

The cut-sheet feeder feeds more than one sheet at a time.Cause What to doYou m ay have load ed toomany sheets in the bin.Remove some sheets. Thehigh

When you try to load single-sheet paper manually, the printerloads the paper from the cut-sheet feeder.Cause What to doThe paper was not properlyloade

Your interface cable does notmeet the printer and/ orcomputer specifications.Use an interface cable that meets therequirements of both the printer and

The printer makes a strange noise and stops abruptly.Cause What to doThe paper is jammed. Clear the paper jam as described onpage 7-24.The ribbon is

Lines of dots are missing in the printout.Cause What to doThe print head is damaged. Stop printing and contact your dealerto have the print head repla

The typestyles or characters set in your application softwarecannot be printed.Cause What to doYour application software isnot correctly configured fo

The top margin or loadingposition setting is incorrect.Check and adjust the margin andloading position settings in yoursoftware. See the printable are

The printout has extra blank lines between lines of text.Cause What to doTwo line feed commands arebeing sent at the end of eachline of text.Turn off

Printing starts lower on the page than you expect, or thebottom of a page is printed at the top of the next page.Cause What to doThe lines-per-page, t

❏ Software, including a printer driver and a remote controlpanel utility, that lets you change printer settings quickly andeasily❏ Bidirectional commu

Clea ring a Pa per Ja m To clear a paper jam, follow these steps: 1 Press the Operate button to turn off the printer.2. Open the printer cover.3. If

Follow the steps below to perform bidirectional adjustment.Note:❑To print the instruction sheet and alignment patterns, you needfour sheets of A4 or l

Appendix ASpecificationsProof Sign-off:Ya n o _______Kim u ra _______G ra d y _______No rum _______Technical Specifications . . . . . . . . .

Technical Specifications Prin t ingPrinting method: 24-pin impact dot matrixPrinting speed:Characters per inch Quality Characters/second/line10 c pi H

Buffer: 64KB or 0KB (selectable in thedefault-setting mode or the EPSONRemote! utility)Bitmap fonts:Font Characters per inch availableEPSON Draft 10,

Pa p e rNote:Use recycled paper, labels, envelopes, and postcards only under normaltemperature and humidity conditions, as follows: Temperature 15°

Continuous paper (ordinary and multi-part):Width 101 to 304.8 mm (4.0 to 12.0 inches)Length/ page 101 to 559 mm (4.0 to 22.0 inches)Copies 1 original

Envelopes:Size No. 6 165 × 92.1 mm(6.5 × 3.6 inches)No. 10 241 × 105 mm(9.5 × 4.1 inches)Thickness 0.16 to 0.52 mm (0.0063 to 0.020 inches)Any differe

Printable area:Single sheetsContinuous paperA The minimum top and bottom margins (above and below theperforation) are 4.2 mm (0.17 inches).B The min

LabelsEnvelopes and postcardsA The minimum top and bottom margins a re 0 mm (0 inc hes).B The minimum left and right margins are 3.0 mm (0.12 inc hes)

How to Use This Manual This manual provides illustrated, step-by-step instructions forsetting up and operating your printer. Chapter 1 contains inform

Roll paperMechanicalPaper feed methods: Friction feed from frontBuilt-in push tractorCut-sheet feeder (optional)Roll paper holder (optional)Ribbon: Bl

Electrical120 V model:Rated voltage AC 120 VInput voltage range AC 103.5 to 132 VRated frequency range 50 to 60 HzInput frequency range 49.5 to 60.5 H

Safety approvals120 V model:Safety standards UL1950 with D3CSA C22.2 No.950 with D3EMI FCC part 15 subpart B class BCSA C108.8 class B230 V model:Safe

Parallel Interface Specifications The printer comes with a bidirectional, 8-bit, parallel interface and anoptional interface slot.Forward channelTrans

Optional Cut-Sheet Feeder Specifications The specifications below apply to both the high-capacity cut-sheet feeder(C80678✽, bin 1) and the second-bin

Environmental:Temperature Operation: 5° to 35°C (41° to 95°F)Storage: −30° to 60°C (−22° to 140°F)Humidity (without condensation)Operation: 10% to 80%

Appendix BCommand Lists and Character TablesProof Sign-off:Ya n o _______Kim u ra _______G ra d y _______No rum _______EPSON ESC/ P 2 Control Codes .

EPSO N ESC / P 2 C o ntro l C o d e s Selecting EPSON ESC/ P 2 printer in your software allows you to use themost advanced font and graphics handlin

Barcode commandYour printer has powerful barcode printing capabilities and includes thefollowing resident barcode fonts: EAN-13, EAN-8, Interleaved 2

c: Control flagBit 0 = Check digit 0: The printer does not add a check digit. 1: The printer adds a check digit.Bit 1 = Human readable chara

Warnings, Cautions, a nd Notes This guide uses the following conventions:wWarnings must be followed to avoid bodily injury.cCautions must be observed

The valid data of each barcode type is described below. If invalid data isincluded in the barcode data string, the barcode is not printed.Ba rc o d e

IBM 2390 Plus Emulation Control Codes This printer emulates the IBM Proprinter with the following commands.For detailed information, see the IBM 2390

Character Tables in EPSON ESC/P 2 Mode When the printer is in EPSON ESC/ P 2 mode, the character tables belowcan be selected using software commands.A

PC850 (Multilingual) PC860 (Portuguese)PC863 (Canadian-French) PC865 (Norwegian)A-8, A-9A-10, A-11LAdonis Rev.CA5 size Appendix B96/ 12/ 19 pass 5B-8

PC861 (Icelandic) BRASCII (Brazilian Portuguese)Abicomp (Brazilian Portuguese) ISO Latin 1A-12, A-13A-14, A-15BRAdonis Rev.CA5 size Appendix B96/ 12/

Ro m a n 8PC437 Greek (Greek)* PC869 (Greek)*A-16, A-17A-18, A-19LAdonis Rev.CA5 size Appendix B96/ 12/ 19 pass 5B-10 Command Lists and Character

ISO 8859-7 (Latin/Greek)* PC853 (Turkish)*PC857 (Turkish)* ISO Latin 1T (Turkish)*A-20, A-21A-22, A-23BRAdonis Rev.CA5 size Appendix B96/ 12/ 19 pass

PC855 (Cyrillic)* PC866 (Russian)*PC852 (East Europe)* MAZOWIA (Poland)*A-24, A-25A-26, A-27LAdonis Rev.CA5 size Appendix B96/ 12/ 19 pass 5B-12

Code MJK (CSFR)* Bulgaria (Bulgaria)*PC864 (Arabic)* Estonia (Estonia)*A-28BRAdonis Rev.CA5 size Appendix B96/ 12/ 19 pass 5Command Lists and Characte

PC774 (LST 1283:1993)* ISO 8859-2*PC866 LAT. (Latvian)* ItalicNo character isavailable for hexcode 15 in the italiccharacter table.LAdonis Rev.CA5 siz

Chapter 1Setting Up the PrinterProof Sign-off:Ya n o _______Kim ura _______Gra d y _______No ru m _______Unpacking the Printer . . . . . . . .

Characters available with the ESC ( ^ commandTo print the characters in the tables below, use the ESC ( ^ command. Thecharacters in the right table ar

The following seven additional sets can be selected only with the ESC Rcommand.A-32LAdonis Rev.CA5 size Appendix B96/ 12/ 19 pass 5B-16 Command L

Appendix CContacting Customer SupportProof Sign-off:Ya n o _______Kim u ra _______G ra d y _______No rum _______For United States Users . . . .

If your printer is not operating properly and you cannot solve theproblem using the troubleshooting information in this guide, contactcustomer support

If you need help using software with an EPSON product, see thedocumentation for that program for technical support information.Electronic support serv

For United Kingdom and the Republic of Ireland Use rs If you purchased your printer in the UK or the Republic of Ireland, Epson (UK) Limited provides

Fa xo n EPSO NContact Faxon EPSON Faxback Service for:❏ Literature and specifications on the latest EPSON products❏ Support information including trou

For Austra lia n Use rs EPSON Australia wishes to provide you with a high level of CustomerService. As well as this User’s Guide, we provide the follo

EPSO N He lp d e skEPSON Helpdesk is provided as a final backup to make sure our clientshave access to advice. Operators on the Helpdesk can aid you

For Hong Kong Users To obtain technical support as well as other after-sales services, users arewelcome to contact EPSON Hong Kong Limited.Internet ho

This chapter describes how to set up your printer and connect it to your computer.Unpacking the Printer Besides this guide, your printer box should in

For Philippines Users To obtain technical support as well as other after sales services, users arewelcome to contact the EPSON Philippines Representat

GlossaryASCIIAmerican Standard Code for Information Interchange. A standardizedcoding system for assigning numerical codes to letters and symbols.auto

data dumpSee hex dump.defaultA value or setting that takes effect when the equipment is turned on, reset, or initialized.ditheringA way of arranging d

high-speed draftA mode of draft printing you can select using the default-settings mode or the EPSON Remote! utility. High-speed draft uses a minimum

tear offA control panel button that feeds the perforation of continuous paper to the tear-off position and then feeds the paper back to the top-of-for

IndexAAdjustingloading position, 3-27−29printing position, 3-29−30tear-off position, 3-31−32AGM (Alternate Graphics Mode)setting, 4-14Assembling the p

DDefault-setting mode, 4-9−15option descriptions, 4-10−14options table, 4-9−10changing, 4-14−15Dithering setting, 2-8, 2-12DOS, 2-12−14Double-bin cut-

MMicrosoft Windows. See WindowsMicro Adjust, 3-27−32loading position, 3-27−29printing position, 3-29−30tear-off position, 3-31−32Multi-part forms, 3-2

RRelease lever. See Paper release leverRemote!. See EPSON Remote!Resolution setting, 2-8, 2-11Ribbon cartridgeinstalling, 1-6−8replacing, 6-2−5Roll pa

Save all packing and protective materials in case you need to shipthe printer in the future. It should always be transported in itsoriginal packaging

Printe r Pa rtsProof Sign-off:Ya n o _______Kim ura _______Gra d y _______No ru m _______paper supportparallel interfac esprocket unitsA2control panel

Note for French-speaking users:Placez l’imprimante près d’une prise de contact où la fiche peut être débranchée facilement.❏ Avoid electrical outlets

Assembling the Printer Installing the knobInsert the knob into the hole on the side of the printer and rotate it slowly until it slips onto the shaft.

Installing the ribbon cartridgeBefore installing the ribbon cartridge, make sure that the powercord is not plugged into an electrical outlet.To instal

2. Slide the print head to the middle position where the front metal plate is indented as shown below.3. Turn the ribbon-tightening knob in the direct

4. Hold the ribbon cartridge with the exposed ribbon down and the ribbon-tightening knob facing you, and guide the ribbonunder the print head. Then sn

Attaching the paper guideTo attach the paper guide, slide the slots on the paper guide all theway onto the mounting pegs in the printer as shown below

Connecting the Printer to Your Computer To connect your computer to your printer’s built-in parallelinterface, you need a shielded, twisted-pair paral

3. Squeeze the wire clips together until they lock in place on bothsides of the connector. 4. If your cable has a ground wire, connect it to the print

Chapter 2Se tting Up Yo ur So ftw a reProof Sign-off:Ya n o _______Kim ura _______Gra d y _______No ru m _______For Windows 95 Users . . . . .

The EPSON printer driver disk that comes with your printerincludes the printer driver software and a printer utility.A printer driver is software that

FCC Compliance StatementFor United Sta te s Use rsThis equipment has been tested and found to comply with the limits for a Class B digitaldevice, purs

3. First turn on your printer and then turn on the computer. Your computer begins loading Windows 95. 4. If you use a password, enter it at the prompt

Installing the printer driver using My ComputerIf you have trouble installing the printer driver using theplug-and-play feature, follow the steps belo

7. Click the Ha ve Disk button to indicate you will install the driversupplied with your printer. The following screen appears:8. Insert the printer d

12. You can type a unique name for the printer in the Printer namebox. We recommend that you keep the model name as shown.Select the Ye s or No radio

Accessing the printer driver from Windows applicationsWhen you access the printer driver from a Windows application,any settings you make apply only t

Checking and cha nging printer driver settingsBefore printing, check that the printer driver settings on the Paperand Graphics menus are appropriate f

For Windows 3.1 Users Installing the printer driver using Progra m Ma nagerFollow the steps below to install the printer driver for Windows 3.1.1. Ma

Windows will now use the LQ-670 as its default printer on port LPT1. If you need to change the default printer or the portassignment, use the Control

Accessing the printer driver from the Control PanelWhen you access the printer driver from the Windows 3.1 Control Panel, the settings you make apply

❏ Paper Source Click the paper source you want to use.❏ Orientation Select Po rt ra it or La n d sc a p e. The diagram on the screen changes according

Declaration of ConformityAccording to ISO/IEC Guide 22 and EN 45014Manufacturer: SEIKO EPSON CORPORATION Address: 3-5, Owa 3-chome, Suwa-shi,Nagano-ke

Choose the EPSON LQ-670 printer at the appropriate step in theprocedure. If the list in your application does not include theLQ-670 printer, choose th

Using the EPSON Remote! printer utilityThe EPSON Remote! utility is included with the printer. Thisutility allows you to change the printer’s default

Chapter 3Paper HandlingProof Sign-off:Ya n o _______Kim ura _______Gra d y _______No ru m _______Selecting a Paper-Feeding Method . . . . . .

Your printer can print on a wide variety of paper types, includingsingle sheets, continuous paper, multi-part forms, labels,envelopes, postcards, and

Paper-feeding methods and paper typesThe table below shows which paper-feeding method to select foreach paper type. You use the paper release lever to

Setting the paper release leverYou use the paper release lever to set the paper path you want theprinter to use. The paper release lever has two posit

Adjusting the Paper Thickness Lever You need to set the paper thickness lever to match the thickness of your paper. When you print on ordinary single-

The following table provides guidelines for selecting theappropriate lever position for the type of paper you are using.Paper type Paper thickness lev

Follow these steps to load single sheets:1. Make sure that the printer is off and the paper guide is attachedas described in Chapter 1. Then close the

4. Slide the right edge guide until it rests against the guide mark, as shown below.5. While adjusting the left edge guide to match the width of yourp

Safety Informa tionImportant Sa fety Instructions Read all of these instructions and save them for later reference. Follow allwarnings and instruction

After printing a sheet, the printer ejects the printed sheet onto thepaper guide and the Pa p er O ut and Pa u se lights come on. If you are printing

Positioning your continuous paper supplyWhen you load continuous paper, make sure you align your paper supply with the tractor so the paper feeds smoo

Loading continuous paper with the tractor1. Make sure the printer is turned off. Set the paper release lever to the tractor position, as shown below.

3. Release the sprocket lock levers by pushing them up.4. Facing the back of the printer, position the left sprocket unit sothat the sprocket pins are

5. Slide the right sprocket unit to roughly match the width of yourpaper, but do not lock it.6. Slide the paper support midway between the two sprocke

7. Open the sprocket covers.8. Fit the first three holes of the continuous paper over the sprocket pins on both sides. Be sure to load your paperprint

9. Close the sprocket covers. If necessary, unlock and reposition the left sprocket unit so that the perforation aligns with thearrow mark on the prin

11. Press the Operate button to turn on the printer. When theprinter receives data, it automatically loads the paper beforeprinting.When using continu

If the perforation between pages is not aligned with the tear-offedge, you can adjust the tear-off position using the micro-adjustfeature as described

2. Tear off all printed pages. If the perforation is not aligned with the tear-off edge, adjust the tear-off position using themicro-adjust feature. S

❏ Unplug the printer and refer servicing to qualified servicepersonnel under the following conditions:If the power cord or plug is damaged; if liquid

For instructions on how to activate the auto tear-off function, see“Using the Default-Setting Mode” in Chapter 4 or open theEPSON Remote! utility as d

Removing continuous paper1. After you finish printing, press the Tear Off/Bin button. Theprinter advances the paper to the tear-off position.Note:When

You can load single-sheet multi-part forms from the paper guideor with the optional cut-sheet feeder. For instructions, see “UsingSingle Sheets” on pa

cCaution:❏When printing on labels, make sure that your softwaresettings keep the printing entirely within the printablearea. Printing on the edge of a

Using Envelopes You can print on a variety of envelopes, loading them in the sameway as you load single sheets: from the paper guide or with theoption

Using Postc a rds You can print on a variety of postcards, loading them in the sameway as you load single sheets: from the paper guide or with theopti

Switching Between Continuous Paper and Single SheetsWhen using the tractor, you can easily switch between continuouspaper and single sheets (including

4. Move the paper release lever back to the single-sheet position.Now you can load single sheets from the paper guide. Forinstructions, see “Using Sin

3. Move the paper release lever forward to the tractor position.The printer automatically advances the continuous paper from thestandby position to th

1. Make sure the printer is turned on. If necessary, lift up theprinter cover so you can see the paper position.2. Load either continuous or single-sh

For Unite d Kingdom Use rs Use of optionsEpson (UK) Limited shall not be liable against any damages orproblems arising from the use of any options or

❏ If you want to eliminate the top margin and print at the very top ofthe page, adjust the loading position so that the top of the paper linesup with

2. Hold down the Pa use button for about three seconds. ThePa u se light begins flashing and the printer enters themicro-adjust mode.3. If necessary,

Adjusting the tear-off position If your paper perforation is not aligned with the tear-off edge, you can use the micro-adjust feature to move the perf

3. Press the LF/ FF [ D] button to feed paper forward, or press the Load/Eject [ U] button to feed paper backward, until the paper perforation is alig

Chapter 4Using the Control PanelProof Sign-off:Ya n o _______Kim u ra _______G ra d y _______No rum _______Basic Control Panel Functions . . . .

This chapter explains how you can use the control panel to controlthe basic operation of the printer and to perform more advancedoperations, such as m

Lig h tsPa p e r O ut (red)On when the printer runs out of paper. Flashes when the paper isja m m e d .Pa use (orange)On when the printer is not rea

Te a r O f f / Bin (two lights, green)The printer uses the two Te a r O f f / Bi n lights to indicate thefollowing: f fThe perforation of your c

LF/ FF (line feed/ form feed)Press this button briefly to feed the paper forward one line. Hold it down to eject a single sheet or advance continuous

Fo n t Sa m p l eDraftRo m a nSa n s Se rifCourierPre stigeSc ri p tOCR-B*Orator*Orator-S*Sc ri p t C *Ro m a n T*Sa n s Se rif H** If one of these

ContentsIntroductionFeatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-1Options . .

When the optional cut-sheet feeder is installed, press this button toselect the cut-sheet feeder bin you want to use. Select Bin 1 to usethe high-cap

Bid irec tional a d justment = Pa useTurns on the bidirectional adjustment mode, which allows you to correct printing alignment problems. See “Using B

Using the Default-Setting Mode The default settings control many printer functions. While you canoften set these functions through your software or pr

Option SettingsCharacter table Standard model:Ita lic, PC437, PC850, PC860, PC863, PC865, PC861, BRASCII, Ab icomp , ISO Latin 1, Roman 8All o ther mo

Skip-over-perforationThis feature is available only when continuous paper is selected.When you turn on this feature, the printer provides a one-inch(2

I/F (interface) modeThe printer has space for one optional interface in addition to itsbuilt-in parallel interface. You can choose automatic, parallel

0 slashThe zero character has a slash (0) when this feature is on; it has no slash (0) when this feature is off. The slash allows you to easilydisting

AGM (Alternate Graphics Mode)When AGM is on, the printer can use advanced graphicscommands like those available in ESC/ P 2 mode. This feature isavail

1. Make sure paper is loaded, then turn off the printer. Whileholding down the Fo n t button, press the Operate button to turn on the printer. The pri

Using Quiet Mode In quiet mode, the printer makes less noise when it prints.However, printing in quiet mode reduces the printing speed.To turn on quie

Chapter 3 Paper HandlingSelecting a Paper-Feeding Method . . . . . . . . . . . . . . . . . . 3-2Paper-feeding methods and paper typ

Chapter 5Using Printer OptionsProof Sign-off:Ya n o _______Kim u ra _______G ra d y _______No rum _______Cut-Sheet Feeders . . . . . . . . .

This chapter describes how to use optional equipment with your printer, including cut-sheet feeders, a roll paper holder, and interface cards.Cut-Shee

You can load up to 150 single sheets of paper, 40 single-sheetmulti-part forms, 25 envelopes, or 50 postcards in thehigh-capacity cut-sheet feeder (bi

3. Move the paper release lever to the single-sheet position.4. Hold the cut-sheet feeder by placing your hands on both sides of it. While holding dow

7. Pull out the sheet guide extension until it is fully extended. (If you do not plan to stack the printed sheets, you do not need to perform this ste

Note:Even when you are not using the cut-sheet feeder, you can use its sheetguide instead of the standard paper guide; simply close the sheet guide’se

Loa ding paper from the high-capa city cut-sheet feederLoad paper in the high-capacity cut-sheet feeder (bin 1 of thedouble-bin feeder) as follows:1.

3. Slide the right paper guide so that its edge is even with the guide mark on the cut-sheet feeder and push back the lever to lock the paper guide in

5. Fan a stack of paper (up to 150 sheets); then tap the sides andbottom of the stack on a flat surface to even it up. cCaution:Do not use labels in t

7. Push back the paper set levers to clamp the paper against theguide rollers.8. Before printing, make sure the paper release lever is set to thesingl