Epson Stylus Color II Ink Jet Printer Guía para resolver problemas descargar pdf (Pagina 11)

You can clean one or both print heads. Each cleaning cycle

takes about one minute. During the cleaning cycle, the

carriage moves and you can hear the printer recharging the

print heads. The

Pause

light flashes throughout the cleaning

cycle and then stays on when the cycle is finished.

To clean the color print head:

1. Make sure the printer is turned on and press the

Pause

button.

2. Hold down the

Alt

button and press

Print Mode

. The

cleaning cycle begins.

3. Press the

Pause

button to resume printing.

To clean the black print head:

1. Make sure the printer is turned on and press the

Pause

button.

2. Hold down the

Alt

button and press

Economy/Condensed

. The cleaning cycle begins.

3. Press the

Pause

button to resume printing.

It can sometimes take up to five cleaning cycles to improve

print quality.

Replacing Ink Cartridges

The printer’s

Ink Out

(black) and

Ink Out

NNN

(color)

lights tell you when your ink cartridges are low on ink and

when you need to replace them. If one of these lights flashes,

the indicated cartridge is low on ink; if it remains on, you

need to replace the cartridge.

Caution:

❏ Do not replace an ink cartridge unless its

Ink Out

light

tells you to. If you replace a cartridge before its light

flashes, the sensor that tells you when ink is out will not

work properly with the new cartridge.

❏ Leave the old cartridge installed in the printer until you are

ready to replace it with a new one. Attempting to print

without a cartridge installed can damage the printer.

❏ If you replace a cartridge when the

Data

light is on, you

must turn off your printer and then turn it back on. This

erases the data received by the printer and you must resend

your print job.

Once you install the ink cartridges, do not open the clamps or

remove the cartridges except to replace them with new ones.

Once you remove a cartridge, you cannot reuse it.

When the color ink cartridge is empty, you can continue

printing with the black ink cartridge by switching to

monochrome mode. To do this, turn off the printer, then turn

it back on and resend your print job. If the black ink cartridge

is empty, you cannot continue printing, even if the color

cartridge still contains ink.

Selecting the Correct Ink Cartridges

Use only these EPSON ink cartridges:

Black ink cartridge S020047

Color ink cartridge S020049

Caution:

Use only genuine EPSON ink cartridges and do not refill

them. Other products may cause damage to your printer that

is not covered by EPSON’s warranties.

Removing and Installing Ink Cartridges

Follow these steps to replace either or both ink cartridges:

1. Make sure the printer is on.

2. Press the

Pause

button (the

Pause

light comes on).

3. Lower the output tray on the front of the printer and then

lift up the printer’s cover by the notches on its sides.

4. Hold down the

Alt

button for about five seconds until the

print head moves slightly left to the ink cartridge install

position. The

Pause

light begins blinking. (The carriage

returns to the home position after 30 seconds if the ink

cartridges are not removed.)

5. Pull up the cartridge clamp to open it. The cartridge rises

partially out of the printer.

6. Lift the cartridge out of the printer and dispose of it

carefully so any excess ink does not spill out. Do not take

the used cartridge apart or try to refill it.

7. Open the package containing the ink cartridge and remove

the cartridge from its foil wrapper. Remove the tape seal

from the top of the cartridge.

Caution:

You must remove the tape seal from the top of the

cartridge; leaving the tape on will permanently damage it.

Do not remove the tape seal from the bottom of the

cartridge; ink will leak out.

8. Lower the ink cartridge into its holder with the label facing

up and the arrow pointing to the back of the printer.

9. Push down the ink cartridge clamp until it locks in place.

10.Press the

Alt

button again. The

Pause

light flashes as the

printer charges the ink delivery system.

11.Close the printer cover. When the charging cycle finishes,

the

Pause

light stops flashing and stays on. Press the

Pause

button to turn off the light and resume printing.

Cleaning the Printer

1. Turn off the printer and disconnect any cables connected to

it. Be sure to keep the printer cover closed as you clean it.

2. Remove any paper or other media from the sheet feeder.

EPSON Stylus COLOR II

Ink Jet Printers 8/1/95 EPSON Stylus COLOR II-11

1 2 ... 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios

Epson Stylus Color II Ink Jet Printer Guía para resolver problemas Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo Epson Stylus Color II Ink Jet Printer