Epson C82363 Especificaciones Pagina 48
- Pagina / 210
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
EPSON EPL-N1600 Chapter 2 Operating Principles
Rev. A 49
which is
g
enerated by convertin
g
the current
flowin
g
throu
g
h the monitorin
g
Photodiode (PD)
inte
g
rated in the LD into an analo
g
output
volta
g
e by means of a resistor.
Scanner Motor Control:
The Poly
g
on Mirror is rotated by the Scanner
Motor (also called ROS Motor). The Scanner
Motor is driven at a constant speed by the
Scanner Motor Drive Circuit usin
g
a phase-
locked loop (PLL).
Mirror ASSY: The Mirror Assembly consists of Mirror M1,
Shutter and PWBA SOS.
Mirror M1:
Reflects the laser li
g
ht beam from the ROS to
the Drum.
PWBA SOS:
Generates a SOS (Start of Scan) si
g
nal. The
laser beam hits a photosensor on the PWBA
SOS at the be
g
innin
g
of each scan, and the
PWBA SOS
g
enerates a pulse si
g
nal (/SOS).
The /SOS si
g
nal is used as the reference timin
g
si
g
nal for
g
eneratin
g
LINE SYNC si
g
nal.
Shutter Mirror:
The Mirror Assembly has a Shutter Mirror (A)
coverin
g
or exposin
g
the Mirror M1 and lens of
the SOS Sensor. When the Cover Assembly
Exit is open, a projection of the Cover pushes
down the crank arm of the Shutter to raise the
Shutter and expose the Mirror M1 and lens of
the SOS Sensor. When the Cover Assembly
Exit is open or the Mirror Assembly is removed,
the Shutter covers the Mirror M1 and lens of the
SOS Sensor to prevent them from collectin
g
dust.
Ima
g
in
g
Cartrid
g
e The Ima
g
in
g
Cartrid
g
e is composed of followin
g
components.
Drum:
An aluminum cylinder with a coatin
g
of
photoconductive material on the surface. The
photoconductive coatin
g
(layer) holds an
electrical char
g
e placed on the surface while in
darkness, and allows the char
g
e to flow throu
g
h
into the conductive layer when exposed to laser
li
g
ht.
BCR (Bias Charge Roll):
Places a uniform electrical char
g
e on the drum
surface, erasin
g
any patterns of decreased
char
g
e remainin
g
from the previous cycle.
Magnet Roll:
Holds toner on the surface in a thin layer and
transports it to the
g
ap between the drum and
the Ma
g
net Roll. Toner is supplied to the
Ma
g
net Roll from the Toner Compartment.
CM Blade (Charging and Metering Blade):
Spreads toner on the Ma
g
net Roll in a thin layer,
and also
g
ives toner a ne
g
ative char
g
e.
Cleaning Blade:
Scrapes the toner remainin
g
after the Transfer
step off of the Drum surface.
- 1
- PRECAUTIONS 3
- About This Manual 4
- Safety Information 5
- Safety Components 6
- Warning/Caution Labels 7
- General Cautions 9
- Revision Status 10
- Table of Contents 11
- Adjustment 12
- Maintenance 12
- Appendix 12
- PRODUCT DESCRIPTION 13
- 1.1 OVERVIEW 14
- 1.2 SPECIFICATIONS 15
- 1.2.2 PAPER SPECIFICATIONS 16
- Rev. A 17 17
- 1.2.5 CONSUMABLES 18
- 1.2.6 OTHER SPECIFICATIONS 18
- Rev. A 19 19
- 1.2.8 OPERATING CONDITIONS 20
- 1.2.9 SAFETY APPROVAL 21
- MAINTENABILITY 22
- Rev. A 23 23
- 1.3 INTERFACE SPECIFICATIONS 24
- 1.3.2 Serial Interface 25
- 1.4 OPERATING SPECIFICATIONS 26
- Rev. A 27 27
- 1.4.1 Panel Settings 28
- Rev. A 29 29
- Rev. A 30 30
- Rev. A 31 31
- 1.4.3 Initialization Process 32
- 1.4.4 Special Functions 33
- 1.4.5 OTHER SPECIFICATIONS 34
- 1.4.5.3 RAM Capacity 35
- 1.4.5.4 Operating Precaution 35
- OPERATING PRINCIPLES 36
- 2.1 OVERVIEW 37
- Rev. A 39 38
- 2.1.2 Paper Transportation 39
- Rev. A 41 40
- Rev. A 42 41
- Rev. A 43 42
- Rev. A 44 43
- Rev. A 45 44
- Rev. A 46 45
- Rev. A 47 46
- Rev. A 48 47
- Rev. A 49 48
- Rev. A 50 49
- Rev. A 51 50
- Rev. A 52 51
- Rev. A 53 52
- Rev. A 54 53
- 2.1.4 Main Control Circuit 54
- TROUBLESHOOTING 55
- 3.1 OVERVIEW 56
- Rev. A 59 57
- 3.1.2 Printer Messages 58
- 3.1.2.1 Status Messages 59
- 3.1.2.2 Error Messages 60
- Rev. A 63 61
- Rev. A 64 62
- Rev. A 65 63
- 3.1.2.3 Warning Messages 64
- 3.2 Troubleshooting 65
- Rev. A 68 66
- Rev. A 69 67
- Rev. A 70 68
- Rev. A 71 69
- Rev. A 72 70
- Rev. A 73 71
- Rev. A 74 72
- Rev. A 75 73
- Rev. A 76 74
- Rev. A 77 75
- Rev. A 78 76
- Rev. A 79 77
- Rev. A 80 78
- Rev. A 81 79
- Rev. A 83 81
- Rev. A 84 82
- Rev. A 85 83
- Rev. A 86 84
- Rev. A 87 85
- Rev. A 88 86
- Rev. A 89 87
- Rev. A 90 88
- Rev. A 91 89
- Rev. A 92 90
- Rev. A 93 91
- Rev. A 94 92
- Rev. A 95 93
- Rev. A 96 94
- Rev. A 97 95
- Rev. A 98 96
- DISASSEMBLY AND ASSEMBLY 97
- 4.1.2 Tools 99
- 4.1.3 Pre-Shipment Check 99
- Rev. A 4-102 100
- 4.2 DISASSEMBLY AND ASSEMBLY 101
- 4.2.1 Cover Side,E 102
- 4.2.2 Shield Assembly Top.ST 103
- 4.2.3 Control Panel 104
- 4.2.4 Cover Assembly MBF.E 105
- 4.2.5 Tray Assembly MBF.E 106
- 4.3 Cover Assembly,E 107
- 4.3.1 Cover Assembly Exit,E 108
- Rev. A 4-111 109
- 4.3.3 Drive Assembly 110
- 4.3.4 Solenoid Feed 111
- Rev. A 4-114 112
- Rev. A 4-115 113
- 4.3.7 Roll Assembly Feed 114
- 4.3.8 Actuator No Paper 115
- 4.3.9 Roll Assembly Turn 116
- Rev. A 4-119 117
- Rev. A 4-120 118
- 4.3.12 Actuator Registration 119
- Rev. A 4-122 120
- 4.3.14 Chute Exchange 121
- Rev. A 4-124 122
- 4.3.16 Solenoid Exchange 123
- 4.3.17 Gear Duplex Assembly 124
- Rev. A 4-127 125
- 4.3.19 Frame Assembly MBF 126
- 4.3.20 Solenoid MBF 127
- 4.3.21 Roll Assembly MBF 128
- 4.3.22 Holder Gear MBF 129
- 4.3.23 Gear Assembly MBF 130
- Rev. A 4-133 131
- 4.3.25 Sensor No Paper MBF 132
- Rev. A 4-135 133
- Rev. A 4-136 134
- Rev. A 4-137 135
- 4.3.29 Actuator-Exit 136
- Rev. A 4-139 137
- 4.3.31 Fuser Assembly 138
- Rev. A 4-141 139
- 4.3.33 Thermostat and Fuse 140
- 4.3.34 Roll Assembly Exit 141
- 4.3.35 Roll-Pinch 142
- Rev. A 4-145 143
- 4.3.37 ROS Assembly 144
- 4.3.38 Mirror Assembly 145
- 4.3.39 Roll Assembly BTR 146
- 4.3.40 Sensor Toner 147
- Rev. A 4-150 148
- 4.3.42 Drive Assembly-F/P 149
- 4.3.43 Drive Assembly Main 150
- Rev. A 4-153 151
- 4.3.45 Fan IOT 152
- 4.3.46 Chassis Assembly PS 153
- W ARNING 154
- 4.3.48 PWBA Hotaru 155
- 4.3.50 Latch R and Latch L 157
- 4.3.51 Shaft Latch 158
- 4.3.52 Guide R (A) and (B) 159
- 4.3.53 Guide CST R 160
- ADJUSTMENT 161
- Rev. A 164 162
- MAINTENANCE 163
- 6.1 OVERVIEW 164
- APPENDIX 165
- 7.1 Electrical Connection 166
- 7.1.2 Master Wiring Diagram 167
- Rev. A 170 168
- Rev. A 171 169
- Rev. A 172 170
- Rev. A 173 171
- Rev. A 174 172
- Rev. A 175 173
- Rev. A 176 174
- Rev. A 177 175
- Rev. A 178 176
- Rev. A 179 177
- Rev. A 180 178
- 7.2 Exploded Diagram 179
- Rev. A 183 181
- Rev. A 185 183
- Rev. A 187 185
- Rev. A 189 187
- Rev. A 191 189
- Rev. A 193 191
- Rev. A 195 193
- Rev. A 197 195
- Rev. A 199 197
- Rev. A 201 199
- Rev. A 203 201
- Rev. A 205 203
- Rev. A 207 205
- 7.3 Circuit Schematics 207
Relacionado con productos y manuales para Servidores Epson C82363
Servidores Epson 802.11g Manual de usuario
(4 paginas)
(4 paginas)
Servidores Epson C82363 Manual de usuario
(34 paginas)
(34 paginas)
Servidores Epson C82362 Manual de usuario
(82 paginas)
(82 paginas)
Servidores Epson C82363 Especificaciones
(56 paginas)
(56 paginas)
Servidores Epson TWAIN PRO Network Guía de usuario
(159 paginas)
(159 paginas)
Servidores Epson GT-30000 Guía de usuario
(148 paginas)
(148 paginas)
Servidores Epson 80211b Manual de usuario
(257 paginas)
(257 paginas)
Servidores Epson 80211b Guía de usuario
(302 paginas)
(302 paginas)
Servidores Epson 80211b Guía de usuario
(68 paginas)
(68 paginas)
Servidores Epson C12C824221 (Net 802.11g Wireless External Print Server) Manual de usuario
(6 paginas)
(6 paginas)
Servidores Epson Equity 386/33 PLUS Guía de usuario
(196 paginas)
(196 paginas)
Servidores Epson C82363 Especificaciones
(199 paginas)
(199 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales