Epson TM-T88II Series Manual de instrucciones Pagina 72
- Pagina / 154
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rev. A Handling, Maintenance, and Repairs 3-5
TM-T88 Series Technical Manual
2. Loosen the adjustment screw with a coin or flathead screw driver.
3. Move the tab up to the upper position.
4. Tighten the adjustment screw, and check to be sure that the detecting lever moves freely.
5. Replace the paper roll.
Note:
For your reference, this shows the diameter at which the near-end sensor is triggered. Note that this
figure is a calculated value, and there may be some variations depending on the printer.
About the mounting position of the paper near end sensor
This printer has a function to allow you to change the mounting position of the paper near end
sensor. This function is used when you mount the printer on a wall.
This is the procedure to change the mounting position:
1. Loosen the detector screw with a coin or similar tool. Turn the screw at least 3 or 4 times.
2. Push the detector lever in until it touches the back of the hole.
3. While pushing the lever, turn the knob toward you until the detector lever clicks into place
in the other hole.
4. While pressing the knob toward you, secure the detector screw.
5. Make sure the detector lever moves smoothly.
Figure 3-2
Position Trigger point (diameter of paper roll)
Lower position About 23mm
Upper position About 27mm
ERROR
POWER
PAPER
OUT
FEED
Knob
Detector screw
Detector lever
- TM-T88 Series 1
- SEIKO EPSON CORPORATION 4
- Modular type connectors 5
- FCC CLASS A 5
- Introduction 6
- WARNING: 7
- Revision Sheet 8
- Contents 9
- Rev. A vii 11
- Chapter 1 13
- Printing Specifications 14
- Character Specifications 15
- Auto Cutter 15
- Paper Roll Supply Device 16
- Paper Specification 16
- Printable Area 17
- Internal Buffer 18
- Electrical Specifications 18
- Reliability 19
- Environmental Conditions 20
- Connectors 21
- Power Supply Connector 22
- CAUTIONS: 24
- RS-232 serial interface 25
- (continued) 27
- Reset switching 29
- Reset DC characteristics 29
- Buttons and Switches 30
- Panel Button 31
- DIP Switches 31
- Transmission speed 32
- DIP switch 2 32
- Print density selection 32
- For parallel interface model 33
- DIP switch 1 33
- DIP switch 2 33
- Panel LED 34
- Self-test 35
- Hexadecimal Dump 35
- Paper Sensors 36
- Standard Accessories 37
- Consumables 38
- Input specifications 39
- Output specifications 39
- Chapter 2 40
- Circuit Block Diagram 41
- Memory Map 42
- M-T88 Printer Mechanism 43
- Head holding mechanism 44
- Paper feed operation 45
- Thermal head 46
- Paper guide 46
- Frame cover 46
- Main frame 46
- Paper Supply Mechanism 47
- Near end sensor mechanism 48
- Paper end sensor mechanism 48
- Photosensor 49
- Shield plate 49
- Main frame (bottom) 49
- Data input and printing 50
- Cutter Mechanism 51
- Stationary blade mechanism 52
- Movable blade mechanism 52
- Auto cutter operation 53
- Cutter blade knob 53
- Cover Mechanism 54
- Cover open sensor mechanism 55
- Display Mechanism 56
- Display panel 57
- Switch board assembly-B 57
- Push-button 57
- RAM (1M bit) 60
- ROM (2M or 4M bits) 61
- Gate array 61
- Reset circuit 63
- AC_1 AC_2 Operation 64
- HL Clockwise 64
- L H Counterclockwise 64
- H H Brake 64
- Control Panel Control Circuit 65
- DIP Switch Read Circuit 65
- Drawer Kick Control Circuit 65
- Power Supply Circuit 66
- I/F Circuit Board Assembly 67
- Switchboard B 67
- Chapter 3 68
- Printer cover 69
- Control panel 69
- Cutter cover 69
- Cover open button 69
- Loading roll paper 70
- Figure 3-2 72
- Detector screw 73
- Detector lever 73
- Other hole 73
- Problem Solving 74
- CAUTIONS: 75
- Maintenance Procedures 76
- Thermal element 77
- Radiation plate 77
- Print circuit board 77
- Chapter 4 80
- Troubleshooting Flowcharts 81
- POWER does not turn on 82
- PAPER OUT LED does not light 83
- ERROR LED is lit 84
- 4 ERROR LED is flashing 85
- Approx. 160 msec 88
- Using This Manual 92
- Roll paper cover 93
- Cover-thermal-AA 93
- Case-lower-AA block 94
- IC cover 94
- CCS-tite M3x8 94
- Cover-cutter-AA 96
- Case-lower-AA 98
- Mechanism 99
- CPS-tite (O) M3x6 99
- Plate-mechanism 99
- CAUTION: 100
- CAUTION: 102
- Hook part 104
- Switch circuit board 106
- CBS-tite 106
- Cover-frame assembly block 107
- Auto cutter unit block 108
- Paper guide unit block 111
- Cable of pape 112
- Lever-cover open 114
- Tabs on frame assembly 116
- Groove of thermal head 116
- Motor-paper feed-receipt 117
- Frame assembly 118
- Motor (+) Terminal Red 122
- Motor (-) Terminal Black 122
- Microswitch Terminal White 122
- Appendix 127
- Reverse mode 128
- Printer status and signals 129
- RS-485 Serial Interface 131
- Appendix A-8 Rev. A 134
- XON/XOFF Transmit Timing 135
- Data Format When Using RS-485 135
- Printer reception data level 136
- Rev. A Appendix A-11 137
- Appendix A-12 Rev. A 138
- Rev. A Appendix A-13 139
- Appendix A-14 Rev. A 140
- Rev. A Appendix A-15 141
- Appendix A-16 Rev. A 142
- Rev. A Appendix A-17 143
- Case Unit Parts Name List 144
- Rev. A Appendix A-19 145
- Appendix A-20 Rev. A 146
- Overall Exploded Diagram 147
- Rev. A A-22 148
- M-T88 Printer Mechamism 148
- Lubrication Points Diagram 149
- Circuit Board Diagram 150
- RS-232 Interface Board 151
- IEEE 1284 Interface 152
- RS-485 Interface Board 153
- Rev. A A-28 154
Relacionado con productos y manuales para Impresión y escaneo Epson TM-T88II Series
Impresión y escaneo Epson USN 52R Especificaciones
(207 paginas)
(207 paginas)
Impresión y escaneo Epson LX-300+ Guía de usuario
(145 paginas)
(145 paginas)
Impresión y escaneo Epson Stylus Pro 4880 ColorBurst Edition - Stylus Pro 4880 ColorBurst Manual de usuario
(6 paginas)
(6 paginas)
(42 paginas)
Impresión y escaneo Epson 7900CTP Especificaciones
(18 paginas)
(18 paginas)
Impresión y escaneo Epson TM-J2000 Especificaciones
(119 paginas)
(119 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.316 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales